Instrument Cluster Diagram – 87-93

June 20, 2011
By

These diagrams are for a 1987, 1988, 1989, 1990, 1991, 1992, and 1993 Ford Mustang. They show the wiring and pin outs of the instrument cluster.

Wiring Diagram for 87-93 Instrument Cluster

Wiring Diagram for 87-93 Instrument Cluster

1987-1989 Wiring Chart
Pin Number Circuit Circuit Function Pin Number Circuit Circuit Function

1. LG/W Left Turn Signal Indicator
2. BK Ground
3. R/W Temp to Sender
4. R/Y Warning Lamps Feed
5. R/LG Ignition Switch to Coil-Batt
6. LG/R Ignition Switch to Alt Reg
7. P/W Brake Warning Signal Light
8. BK/L Warning Lamp Prove Out2
9. Not Used Not Used
10. GY Low Oil Level to Signal
11. DG/Y Tachometer Feed
12. Not Used Not Used
13. W/LB Right Turn Signal Indicator
14. LG/BK High Beam Indicator

1. GY Low Oil Indicator Lamp
2. R/W Switch to Warning Lamp
3. P/O ??? (Not Used in conversion)
4. Not Used Not Used
5. Not Used Not Used
6. Y/BK Signal Unit Lamp to Fuel Signal Relay
7. PK/Y Washer Fluid Low Indicator
8. Y/BK Signal Unit Lamp to Fuel Signal Relay
9. W/R Oil Pressure Signal
10. Y/W, LB Fuel Gauge Feed/Low Fuel Indicator Relay
11. R/Y Warning Lamps Feed
12. BK Ground
13. DG/LG Coolant Temp Relay Feed
14. LB/R Instrument Panel Lamps Feed

Notes:
If you are attempting to install a 1990-1993 steering wheel in a 1987-1989 car, then the steering column must also be changed. All connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug. This process if much easier if you have an old harness from a 1990-1993 that comes out of the instrument cluster. The wires need to be as long as possible (6-8 inches), and they can be successfully wire tapped and soldered to the factory 1987-1989 harness. 2 Used to test lights when ignition is turned to the “Start” position.

 

Tags: , , , , , , ,

3 Responses to Instrument Cluster Diagram – 87-93

  1. [...] the resistor/light bulb? to be safe, what wire should i wire it to then? i'm using this website: Instrument Cluster Diagram – 87-93 | Mustang Wiring Diagrams so if you happen to know based on those pictures which one to wire it to, i'd really appreciate the [...]

Search This Site


Warning: Unknown: open(/home/users/web/b2234/moo.hissindcom/cgi-bin/tmp/sess_6f31cae5691cc4918cd8bdd951221b20, O_RDWR) failed: No such file or directory (2) in Unknown on line 0

Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/home/users/web/b2234/moo.hissindcom/cgi-bin/tmp) in Unknown on line 0